Edudel Syllabus 2025 Class 12 English

ANNUAL SYLLABUS (2024-25)
CLASS: 12
SUBJECT: ENGLISH CORE (CODE-301)

Section - A Reading Comprehension 22 Marks
Section - B Writing Skills 18 Marks
Section - C Literature 40 Marks
Assessment of Listening and Speaking Skills +Project 20 Marks

TEXTBOOKS READING SKILLS CREATIVE WRITING SKILLS
FLAMINGO Unseen Passage Types: Short Composition
Prose: Factual Passage  Notice Writing
Lesson-1 The Last Lesson Descriptive Passage  Formal/Informal Invitation and replies
Lesson-2 Lost Spring Literary Passage Word limit 50 words
Lesson-3 Deep Water Letter Writing
Lesson-4 The Rattrap Unseen Case Based Factual Based on visual and/or verbal input in 120-
Lesson-5 Indigo Passage 150 words.
With verbal/visual inputs like Letter types:
Poetry: statistical data, charts etc.  Application for a job with Bio Data or
Poem - 1 My Mother at Resume.
Sixty Six The combined Word limit for  Letter to Editor
Poem - 2 Keeping Quiet both the passages will be 700- (Giving suggestions or opinion on issues of
Poem - 3 A Thing of 750 Words. public interest)
Beauty
Article Writing
VISTAS Based on verbal inputs in 120-150 words
Lesson -1 The Third Level (may be descriptive/analytical in nature)
Lesson -2 The Tiger King
Lesson- 3 Journey to the Report Writing
End of the Earth Based on verbal inputs in 120-150 words
Lesson-4 The Enemy (may be descriptive/analytical in nature)

INTERNAL ASSESSMENT

 Assessment of Listening Skills - 05 Marks
 Assessment of Speaking Skills - 05 Marks
 Project Work - 10 Marks

Note:- The above mentioned syllabus should be completed by September 13, 2024

Revision

Mid Term Examination

TEXTBOOKS READING SKILLS CREATIVE WRITING SKILLS
FLAMINGO Unseen Passage Short Composition
Type:  Notice Writing
Prose: Factual Passage  Formal/Informal Invitation and replies
Lesson - 6 Poets and Descriptive Passage Word limit 50 words
Pancakes Literary Passage Letter Writing
Lesson - 7 The Interview Based on visual and/or verbal input in 120-
Lesson - 8 Going Places 150 words.
Unseen Case Based Factual Letter types:
Poetry: Passage  Application for a job with Bio Data or
Poem - 4 A Roadside Stand With verbal/visual inputs like Resume.
Poem - 5 Aunt Jennifer’s statistical data, charts etc.  Letter to Editor
Tigers (Giving suggestions or opinion on issues of
public interest)
VISTAS The combined Word limit for
both the passages will be 700- Article Writing
Lesson -5 On the Face of It 750 Words. Based on verbal inputs in 120-150 words
Lesson-6 Memories of (may be descriptive/analytical in nature)
Childhood
 The Cutting of My Long Report Writing
Hair Based on verbal inputs in 120-150 words
 We too are Human (may be descriptive/analytical in nature)
Beings
INTERNAL ASSESSMENT

 Assessment of Listening Skills - 05 Marks
 Assessment of Speaking Skills - 05 Marks
 Project Work - 10 Marks

Note: -
 All the syllabus should be completed by December 13, 2024
 In Pre-Board/Annual Examination, questions will be asked from the entire syllabus.

Revision of entire syllabus

Pre-Board/Annual Examination

For more information regarding the syllabus, see CBSE Syllabus Specifications 2024-25.
https://cbseacademic.nic.in/web_material/CurriculumMain25/SrSec/English_core_SrSec_2024-25.pdf

ANNUAL SYLLABUS (2024-25)
CLASS: 12, SUBJECT: ENGINEERING GRAPHICS (Code 046)
THEORY
Unit I: Isometric Projection of Solids
(i) Construction of isometric scale showing main divisions of 10mm and smaller divisions of 1 mm, also
showing the leading angles. Drawing helping view/s such as triangles, pentagon, hexagon, etc., using
isometric scale.
(ii) Isometric projection (drawn to isometric scale) of solids such as cube; regular prisms and pyramids
(triangular, square, pentagonal, and hexagonal); cone; cylinder; sphere; hemisphere. The axis and the base
side of the solid should be either perpendicular to HP / VP or parallel to HP and VP.
(iii) Combination of any two above mentioned solids keeping the base side parallel or perpendicular to HP/VP
and placed centrally together (Axis of both the solids should not be given parallel to HP).
Note:
1. Hidden lines are not required in isometric projection.
2. Indicate the direction of viewing.
Unit II: Machine Drawing (as per SP46: 2003)
A. Drawing of machine parts
(i) Drawing to full size scale with instruments.
(Internal choice will be given between any two of the following).
Introduction of threads: Standard profiles of screw threads - Square, Knuckle, B.S.W., Metric (external
and internal); Bolts – Square head, hexagonal head; Nuts – Square head, Hexagonal head; Plain washer,
Combination of nut and bolt with or without washer for assembling two parts together.
(ii) Free-hand sketches
Conventional representation of external and internal threads; Types of studs – Plain stud, Square-neck
stud, Collar stud; Screws (round-head, cheese-head, 900 flat counter sunk-head, hexagonal socket head
and grub-screw); Types of rivets – Snap head, Pan head (without tapered neck), Flat head, 60 0
countersunk flat head.

Note:- The above mentioned syllabus should be completed by September 13, 2024.

Revision

Mid Term Examination

B. Assembly drawings and Dis-Assembly drawings
(Internal choice will be given between an Assembly drawing and a Dis-Assembly drawing).

1. Bearings
(i) Open-Bearing
(ii) Bush- Bearing
2. Rod-Joints
(i) Cotter-joints for round-rods (Sleeve and cotter joint)
(ii) Cotter-joints for square rods (Gib and cotter-joint)
3. Tie-rod and Pipe-joint
(i) Turnbuckle
(ii) Flange pipe joint
Note:
3. In all Assembly drawings, half sectional front view will be asked. Side/End view or Top View/Plan will be
drawn without section.
4. In all Dis-assembly drawings, only two orthographic views (one of the two views may be half in
section or full in section) will be asked of any two parts only.

5. (a) In all sectional views, hidden lines/ edges are not to be shown.
(b) In all full views, hidden lines/edges are to be shown.

Note: -
 All the syllabus should be completed by December 13, 2024.
 In Pre-Board/Annual Examination, questions will be asked from the entire.
Revision of entire syllabus
Pre-Board/Annual Examination

PRACTICALS
(i) To perform the following tasks (for One only) from the given views of the prescribed fifteen (15)
machine blocks in ANNEXURE-I.
Value-Points
1. Copy the given views 1
2. Drawing the missing view with hidden lines 2
3. Sketching the Isometric view without hidden edges 5
4. To make the machine block of the above in three dimensions.
(Not to scale but approximately proportionately drawn with any medium i.e., Soap-cake,
plasticine, clay, wax, floral foam brick (available with florists), etc.
7

(ii) Computer Aided Design (CAD) – Project 10
Project file to be submitted on the simple solids or machine blocks as prescribed in part-I
by using the CollabCAD software or any equivalent pertinent software.

(iii) (a) Sessional work relating to machine blocks as prescribed. 3
(b) Viva-voce based on part-I and part-II 2

Total Marks 30

ACTIVITY
Industrial Visits (Two) to any industry/ manufacturing plant to acquaint the students with the present -
day methods & technology for better conceptual understanding.

For more information regarding the syllabus, see CBSE Syllabus Specifications 2024-25.